RC RT
Well-Known Member
- Messages
- 90
- Location
- San Ramon Ca.
Very nice
Looks like time to burn some fuel
been looking into doing custom body paint for my 5t 2.0, watching vid's,
but pricing slowing me down, have other upgrades higher on the list
Finished TLR 5ive-B
- Thread starter Squizzy Ralph
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
Very nice
Looks like time to burn some fuel
been looking into doing custom body paint for my 5t 2.0, watching vid's,
but pricing slowing me down, have other upgrades higher on the list
Squizzy Ralph
Member
- Messages
- 12
- Thread starter
- #22
Thanks. Working on break in now. I really like these servos and might upgrade my 2.0 also to them. Hitec D845WPVery nice
Looks like time to burn some fuel
been looking into doing custom body paint for my 5t 2.0, watching vid's,
but pricing slowing me down, have other upgrades higher on the list
I used the zenoah g320 and use all three hitec d845wp.
Your cuts look really clean. What did you use to cut the back by the starter. And what did you use for the rectangle shaped vents?
Also check out these schlock covers. I run them on my 5T and love them.
Attachments
Last edited:
RC RT
Well-Known Member
- Messages
- 90
- Location
- San Ramon Ca.
- Messages
- 8,403
- Location
- Bristol uk
I need me a bart...loads of servo horn clearance....
last pic...is the exhaust exit facing the chassis
..loads of servo horn clearance....last pic...is the exhaust exit facing the chassis
RC RT
Well-Known Member
- Messages
- 90
- Location
- San Ramon Ca.
fegured out how to post
thinking of putting a spacer under mout that should raise above and also change angle of exhaust pipe to add silicone tube
mount
need to proof read lol
That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it
If I have to will weld a tube to tube to get it out side
Just looked at DDM site the
Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845
NOW thru 6/19 $87.99
wifey NOT going to be happy
yesI need me a bart.
last pic...is the exhaust exit facing the chassis
thinking of putting a spacer under mout that should raise above and also change angle of exhaust pipe to add silicone tube
mount
need to proof read lol
That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it
If I have to will weld a tube to tube to get it out side
Just looked at DDM site the
Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845
NOW thru 6/19 $87.99
wifey NOT going to be happy
Last edited:
- Messages
- 5,829
- Location
- Maryland, USA ??
I don't think you will be able to use that pipe on a 5ive B. The way that pipe goes up, there will not be enough room under the body.
Whoduh
Well-Known Member
- Messages
- 888
- Location
- Fairfax, VA
Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845
NOW thru 6/19 $87.99
wifey NOT going to be happy
don't forget to use coupon code LSF
Brings the price down a few more bucks.
Squizzy Ralph
Member
- Messages
- 12
- Thread starter
- #28
- Messages
- 8,403
- Location
- Bristol uk
doug got one fitted on his ......
- Messages
- 5,829
- Location
- Maryland, USA ??
- Messages
- 8,403
- Location
- Bristol uk
that's not good imo..fegured out how to post
yes
thinking of putting a spacer under mout that should raise above and also change angle of exhaust pipe to add silicone tube
mount
need to proof read lol
That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it
If I have to will weld a tube to tube to get it out side
Just looked at DDM site the
Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845
NOW thru 6/19 $87.99
wifey NOT going to be happy
..r barts this bad a fitting???my 5ive one fits sweet......whats this on btw??a 5 or 5b?
- Messages
- 5,829
- Location
- Maryland, USA ??
I didn't know that...guess it will work then.doug got one fitted on his ......
- Messages
- 8,403
- Location
- Bristol uk
assuming this is a 5b bart....I didn't know that...guess it will work then.
- Messages
- 5,829
- Location
- Maryland, USA ??
Last edited:
- Messages
- 8,403
- Location
- Bristol uk
ahh....mine hangs over side of chassis sweet....
20181021_174933 by evssv, on Flickr
u have 2.0 don't u?is it a 2.0 bart or normal 5 bart one?
mine hangs over side of chassis sweet....20181021_174933 by evssv, on Flickru have 2.0 don't u?is it a 2.0 bart or normal 5 bart one?
Last edited:
Gamefan
Well-Known Member
- Messages
- 684
- Location
- Denver, USA
Your 5T looks sick!
- Messages
- 8,403
- Location
- Bristol uk
thk u...
- Messages
- 17,175
- Location
- Crafers South Australia
Yes i have a bart pipe on my 5bthat's not good imo..
and it fits great Had two issues the end was a bit short so i put radiator hose and clamp on the end. Getting the head pipe tight i had to mod an allenkey and cut the end off
Gaffle
Well-Known Member
- Messages
- 213
- Location
- Atlanta, GA
What did you use to cut your allen key?
Yes i have a bart pipe on my 5b
Had two issues the end was a bit short so i put radiator hose and clamp on the end. Getting the head pipe tight i had to mod an allenkey and cut the end off