gears

  1. E

    57cc gear ratios

    Hay guy I was wondering if anyone can help me. I have a 57cc engine in my baja 5b and am in need off a suitable gear ratio the stock ratio just isn't cutting it please help
  2. M

    Dry lube

    Dry lube use? It is wise to use dry lube, gears, couplings, reducing wear?
  3. voo2doo

    Losi MTXL ..Your opinions count!

    I'm looking into a Losi MT XL and have no clue of what they are like.A few people on here ,especially the older members know I have owned near every large scale thats worth owning but I have never seen one of these trucks in the flesh. So, have any of you folk have or had one , i'd like a good...
  4. RustyMiata

    Opinions on king motor brand servos?

    Just experienced my first runaway on my KM 5B due to the throttle servo being stuck wide open. Car was brand new and has only just been broken in. I heard on other forums that king motor servos ( especially the throttle servo) are junk. Has anyone else here had similar issues with king motor...
  5. Gary McConnell

    Dbxl pinion washers please help

    I am currently build a DBXL from parts when putting the pinion in the diff housing I can not figure what goes where dollar hobby sent me 2 washers or shims with each one black one silver . Which way around to they go . Plus the manual shows 4 washers . Please help
  6. Guardog8

    Considering Selling KM T1000GT Need opinions

    Have a KM T1000GT that is in excellent condition. Upgrades include: Dominator V1 pipe - Walbro 1107 carb - Proline rear tires - HPI wheels - RPM bumpers - will include aluminum bumpers - LED Lights w/ 3rd channel light controller - Uni short filter w/ pre filter, red cover and velocity stack -...
  7. madmanandrewk

    Pinion at 45* from diff case???

    Has anybody seen anything like this before? I know it's a bad picture but you can see that the pinion, bearing and driveshaft and all, have been ripped out of and are at 45* with the diff case. Is this why they sell aluminum diff cases? I was running in gravel so it's possible that a rock...
  8. M

    pinion gear

    my pinion in my 5-t just got all of the teeth stripped off of it. i should have known that was going to happen cause it wasn't lining up right. i would line it up and once i would start driving it it would pop out of place can anyone tell me why it wasn't lining up right and give me some advice...
  9. M

    pinion gear

    my pinion in my 5-t just got all of the teeth stripped off of it. i should have known that was going to happen cause it wasn't lining up right. i would line it up and once i would start driving it it would pop out of place can anyone tell me why it wasn't lining up right and give me some advice...
  10. M

    pinion stripped threads

    my pinion just got all of the teeth stripped off of it. i should have known that was going to happen cause it wasn't lining up right. can anyone tell me why it wasn't lining up right and give me some advice on how to put the new one on and not run into the same problem thank you.
  11. M

    Lipo batteries-opinions on cheapies??

    Looking for opinions on cheapie lipos you guys have used with success. I've been stocking up on 2s lipo's for the kids. Bought some used ones of Ebay with good success, both name brand and no name. Decided to buy new from now on but don't want to shell out $100 a pack if you know what I mean...
  12. D

    Hpi baja pinion/spur gear ratios

    Hey guys, I'm just wondering what the best gear ratio would be for me I am looking for much more top speed, the acceleration is already heaps and I'm more then happy with that. So what I want to know is what the best pinion to spur gear teeth ratio would be for me. At the moment it's at the...
  13. M

    Pinion wrench

    Im having a really hard time trying to remove the 20t pinion of my dbxl. Does anyone know if the team fast eddy pinion wrench for the 5ive, will fit the dbxl pinion??? thanks.
  14. D

    Ring and pinion

    anybody tell me where I might get a spirial bevel gear set for a 1/4 scale dragster I'm building I've tried stock drive com. And qtc. They are stupid high on the price I bought a gear set for my ford 9 inch for 50.00 less then what they want and if I did what it from sdi there out of stock...
  15. D

    DGI gears

    can your mix dgi gears with the stock ones or are they a different cut
  16. R

    DGI Gears

    I was looking on DGI website and they have gear sets. 22/59 23/58 24/57 I'm running the stock motor and a Jetpro pipe. Was thinking of changing the gears but not sure which to go with. According to the site I'll need to change the gas tank as well. How do I figure out my top speed...
  17. 8

    Pinion wobble

    Hi everyone, new here and need some help. Just got some new gears for my baja, Hostile 19/55 pinion spur, and the pinion doesn't seem to seat well. When I try to put it on, it's hard to push on by hand, and I need to use the bolt to get it on the rest of the way. Tried removing, then...
  18. C

    Help With Leopard 5692 Pinion Gear !!

    I need help finding 6mm bore pinion gears. My leopard 5692 has 6mm bore but the motor is 8mm shaft. anybody have guidance on this? I know Kershaw Design sell a bore reducer but he is sold out for a while ! The stock motor in XBE is too slow for my taste :)
  19. X

    Gears

    okay I have searched and not found the answer so I am asking what size gears should I run on my km baja 30cc with dom pipe. I want a quicker jump out of the hole if I lose a little top end I don't care. Thanks for any and all help.
  20. claude bigelow

    Correct gears for the Zenoah G320.

    I just purchased a Zenoah G320 from DDM for my DBXL. I will be putting a Bartolone silenced pipe, and 990 carb. As of now I have stock gears, and wondering if someone can advise me on if I need to change them for better performance. If so which will I need and where I can purchase. Any help...
Top