The ultimate hack😆

[DougStar]

So iv really had a gut full of my hostile boots getting chompped ?? was just finishing up reinstalling my drives when I had a redneck ?? wave??
Take one empty oil bottle
A ruler and Stanley knife??

Hollow punch??

Cut out for the spur??

Some cable ties??

TAAAADDAAAA! Mud guards?

I have 0 to lose cost X8 cable ties ?? pastic is 1mm and has flex..... I rekon my hostile boots will last a few more tanks now????
I

 

[Rep732]

Thats the im broke down on the side of the road and I don't give a fek how I get home jammy right there boy

 

[Haric]

nice little hack there mate! ??

 

[DougStar]

That be my inner redneck right there son?

 

[blackrain]

If you didn’t say anything i would have thought you bought those.

 

[DougStar]

Thats the im broke down on the side of the road and I don't give a fek how I get home jammy right there boy

nice little hack there mate! ??

If you didn’t say anything i would have thought you bought those.

thats what I thought ??

 

[Rep732]

Just ball busting ..im going to have to replace my aluminum ones soon as they got sand blasted pretty bad today

 

[DougStar]

All good bud? all part of the experience ?

Just ball busting ..im going to have to replace my aluminum soon as they got sand blasted pretty bad today

 

[buzzkill]

Nice and they are sponsored by MOTUL !!!

 

[DougStar]

Yip make you go faster

Nice and they are sponsored by MOTUL !!!

 

[buzzkill]

Yip make you go faster??

Love the smell of MOTUL in the morning ! used to run it in my Kart MMMMMMMMMMM

 

[DougStar]

Smells like sweets???

 

[Rep732]

Anyone remember this stuff? you add it to the gas for a nice smell...what could go wrong?

 

[DougStar]

Nice and they are sponsored by MOTUL !!!

And the best part is I have a full bottle on the shelf for the next set of guards????????

 

[Clubin]

That looks better than the t-bone stuff.

 

[buzzkill]

Damn I have a laser cutter make me a template and I'll find some material and make some , its just sitting there so why not ? hey measure the thickness please

 

[DougStar]

Its about 1mm??

Damn I have a laser cutter make me a template and I'll find some material and make some , its just sitting there so why not ? hey measure the thickness please

Do it ??

 

[buzzkill]

Its about 1mm??

Do it ??

Might have to go thinner I have a 50 watt CO2 laser , so maybe .5mm ?? gotta test it with some polyester ( face shield plastic ) poly cuts clean and has no BAD fumes !! lasers can produce really BAD fumes so material matters.

I need a template 1-1 size or basic numbers so I can CAD model it for the laser or 3d printers

Its about 1mm??

Do it ??

If you just outline the part on a piece of paper and right down the lenght and width I can work out the other dimensions , take a Picture of the paper and send it to me or post it .

 

[DougStar]

Ok ill measure whats left of the bottle ?? don't feel like cutting one of the guards off?? give me 5

Might have to go thinner I have a 50 watt CO2 laser , so maybe .5mm ?? gotta test it with some polyester ( face shield plastic ) poly cuts clean and has no BAD fumes !! lasers can produce really BAD fumes so material matters.

I need a template 1-1 size or basic numbers so I can CAD model it for the laser or 3d printers

If you just outline the part on a piece of paper and right down the lenght and width I can work out the other dimensions , take a Picture of the paper and send it to me or post it .

Re measured the plastic definitely 1mm i also neatened up the edges a bit could have been 10mm longer as they don't go all the way to the end of the arms? but as you can see I used what was available ??

 

[buzzkill]

Look close ??? the holes are 0.8cm diameter , I am guessing on stuff