DarkCat project

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
S

Sergio1

Senior Member
Messages
736
Reaction score
7
Location
Providence RI
Hi guys wanted to share my little project so far i have


Redcat xb


Jetpro rear mount pipe


Gizmos racing Modified walbro 257


Dt1 triple flow air filter and outerwears


Hitec 5765 servo


Hitec 5645


DDM tall velocity stack


ADA rc manifold


KM all terrain tires with star wheels


T-bone racing front and rear bumper


On The way i have


7075 chassis


7075 Front and Rear Differential Housing Combo


7075 front and rear bearing holders


7075 c-hubs


Ramtech 24 mm adapters


Phyton motor mount


Maybe(not sure yet) Ill get The RCMK full mod CR300 30.5 engine 36mm bore 30mm stroke if there is any money left on my wallet


Everything else will stay stock till i have more cash
 
Dreggsta said:
could you post a link to those wheels & tires?that motor sounds pretty wicked. :)
Click to expand...
http://www.ebay.com/itm/300742643017?redirect=mobile

This is what i have but Just so You know they don't come with The metal ring that goes where The hex is and i could not find them anywhere so i don't know if You are better off getting The hpi which are suppost to be better
 
Sergio said:
http://www.ebay.com/itm/300742643017?redirect=mobileThis is what i have but Just so You know they don't come with The metal ring that goes where The hex is and i could not find them anywhere so i don't know if You are better off getting The hpi which are suppost to be better
Click to expand...
those are really sweet. thanks for that link. i really like those tires. do you know the height of those tires? very cool. you have a lot of goodies for your cat. i'm jealous. :)
 
Sergio said:
http://www.ebay.com/itm/300742643017?redirect=mobileThis is what i have but Just so You know they don't come with The metal ring that goes where The hex is and i could not find them anywhere so i don't know if You are better off getting The hpi which are suppost to be better
Click to expand...
you talking bout the metal hex that the proline wheels have? the hex is plastic? if so then yeh, i seen that. i started using lock washers w/the wheel nuts in place of the flat washers.
 
They are both 6 1/2 inches tall rears 3 1/4 wide, fronts 2 1/2 wide

Thanks man lot of money invested too but The stuff im waiting For is taking forever i cant wait to get it but don't even know when is coming
 
Sergio said:
They are both 6 1/2 inches tall rears 3 1/4 wide, fronts 2 1/2 wideThanks man lot of money invested too but The stuff im waiting For is taking forever i cant wait to get it but don't even know when is coming
Click to expand...
Sorry for delaying your project man. Keeping up is tough but when the rear holders come in Friday I'll have eveything in stock, for once.
 
Ol said:
Sorry for delaying your project man. Keeping up is tough but when the rear holders come in Friday I'll have eveything in stock, for once.
Click to expand...
No problem You know how it is im here pulling my hair waiting i have everything apart and thanks again
 
Not a lot Of time for this but

dkzc.jpg


oyi0.jpg
 
Com'n along nicely.

You might want to run those kill switch wires out under the engine shroud. I could see them getting pinched there.
 
RCDAD said:
Com'n along nicely.You might want to run those kill switch wires out under the engine shroud. I could see them getting pinched there.
Click to expand...
No if you take a look at the shroud it has a little opening therethe exact size for the wires to exit. I was gonna drill a hole but then i notice that opening the wires fit nice no pinching.
 
Back
Top