Dom pipe for Rampage MT

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
B

bajamaniac69

Well-Known Member
Messages
236
Reaction score
0
Location
Florida
Just wondering.....I have seen youtube footage with rampage MT with a rear Dom pipe installed...


I see that it works..............what mods would be needed???


Thanks


J
 
Yep thats what i did, I also welded up a mounting plate to the pipe to get it to bolt to the rear shock tower. only problem so far is i didn't space it properly and melted the back corner of the body.
 
I have this pipe sent to me by a member to look at fitting. I could make an adapter for the head to header and the bottom mount and a deflector, but WHY? You give $150 bones for the pipe then buy the adapter kit and still got a heavy chromed steel crap hanging off the back.


The dom is good for low end , I know why it is but we need to start from scratch with the Rampage. I will work on ths tuning style of pipe first after the roll cage hoop and the chassis flex brace, please be patient on the dom style pipe. I have got header conversion fixture for the HPI SS and the RD Logcs if you need something to get you by while I get my pipe ready.
 
I snaggged a slightly used dom for $85 add the silicone tubing... I got me a nice pipe for under $100


I don't like the performance of the baja pipe on the baja...don't think i would like it on the rampage:)


I hope there are a couple of rear pipes made just for the MT...Little extra weight in the back helps keep the nose up while jumping;)
 
Last edited by a moderator:
hey just Gerald...what size is your heater hose did you use 3/4 inch ID


I found silicone tubing but its sold 25ft min....which one would work best??


0.750 id x 0.875


od 0.750 id x 0.936


od 0.875 id x 1.061


od 0.875 id x 1.249 od


Any one else need some pm me.... temperatures up to 450* continuous, 550* intermittently.
 
Last edited by a moderator:
Yes I had 3/4 heater hose. but the pipe is really 1" OD so you need to get as big as you can, so the .875 ID, not sure if you would want the thin or thickwall, I would choose thinkwall, but will be harder to get over the pipe.


really we need to find 1" ID tubing, but i haven't had any luck finding any locally
 
what about..1.000" id x 0.1875" wall.....hard to find the right size thicknees
 
Last edited by a moderator:
McMaster Carr part # 51735K32 Braid reinforced, 5.5" bend radius, -80º to 500º temp range. 1" ID, 1.360" OD .180" wall but OUCH! it is $25.27 per FOOT!!!


MOfroggy
 
thanks for the info, I might try that ...other place has the 1" but I have to buy 25ft its only $5.50 a foot... $6 a foot shipped ....if i knew other people needed some I could see getting a roll ...I only need 6-8 inches of the silicone
 
Last edited by a moderator:
well I ordered from both places:) Should have it next week if anyone wants a foot let me know looking to get $10 a foot :rolleyes:
 
Last edited by a moderator:
Hey I have a new rear dom to look at. I think you all might be going the hard way on the mod. To fit try turning the pipe upside down then cut in half at the start of the deflector cone seem and rotate 180 degrees.
 
Thats easier then chopping the header pipe and adding hose? That's the second time you've stated that we are 'idiots' for attempting to put a DDM Baja Dom on the redcat, Well I for one feel that this pipe will FULLY outperform the HPI tuned pipe, and is Much easier to mod, a simple hacksaw is all that is needed. no heat, no bending, no sending my parts to someone else. Can it be fit in there easier, probably, but this works and is quick and easy.
 
Last edited by a moderator:
I beg your pardon I never called anyone an "idiot" I fabricate airplane parts for a living I am merely shedding a different way of looking at a way of doing it with over 15 years of aviation and race car background. You are free to get it on there however you see fit, but some may want to have more than one option. I am sorry you took it the wrong way. I realy don't understand why you think I praise the HPI pipe twice now either. I just fitted the header for those that might be able to obtain one cheap or have a pull off. Just as you all are trying that with DOM, but some might have a problem cutting and welding on a new DOM they just bought for $150 I have seen used HPI pipes for 30 - 50 dollars. I don't just praise there performance but it is a good value while us manufactures get our pipes in to production for this truck.
 
I got to fit up my idea of re clocking the rear DOM to fit the MT

Rampage DOM 001.webp

Rampage DOM 002.webp

Rampage DOM 003.webp

Rampage DOM 004.webp

Rampage DOM 005.webp

/monthly_2008_07/583c605336877_RampageDOM001.jpg.25f23ead232c6e8cfcb8cb0d334137b1.jpg

/monthly_2008_07/583c605338051_RampageDOM002.jpg.c8f3daca4073742c74f3e7c979481c55.jpg

/monthly_2008_07/583c605339667_RampageDOM003.jpg.15b7b644a6e8471fe89825a6a869e273.jpg

/monthly_2008_07/583c60533ad12_RampageDOM004.jpg.4a3d1775d675b9d559d22165f78ef0ff.jpg

/monthly_2008_07/583c6053522c4_RampageDOM005.jpg.163ea643d7924bf57471e769e31c1f15.jpg
 
Back
Top