exhaust repair(jb weld)

[smurfer69]

hi guys
welding is not an option,
will jb weld hold work on this hole ?
and should I use it inside or out ?
its properly 1mm wide by about 10 long very thin

 

[Z.hb71]

hi guys
welding is not an option,
will jb weld hold work on this hole ?
and should I use it inside or out ?
its properly 1mm wide by about 10 long very thinView attachment 46604View attachment 46605

how the heck did that happen? try jb weld then header wrap

 

[smurfer69]

the left hand bolt hole got stripped. long story short
had to replace with bigger thread (bolt)so the nut had to be bigger
which altered the right hand side (hole)so had to grind exhaust
down to be able to do screws up(oops pop goes the hole, poop)

 

[Z.hb71]

the left hand bolt hole got stripped. long story short
had to replace with bigger thread (bolt)so the nut had to be bigger
which altered the right hand side (hole)so had to grind exhaust
down to be able to do screws up(oops pop goes the hole, poop)

Ohh

 

[smurfer69]

too be honest im gonna get new top end kit n
go to 36cc with 4 bolt engine upgrade from 32cc
on my g320.
2 birds with 1 stone

 

[Z.hb71]

too be honest im gonna get new top end kit n
go to 36cc with 4 bolt engine upgrade from 32cc
on my g320.
2 birds with 1 stone

who makes the 36cc? if yur talking the rovan i would honestly go for the obr 34cc cuz more POWER!!!

 

[smurfer69]

have to see the cost of that ill check it out ta

 

[smurfer69]

its the obr just the top end kit ?

 

[Z.hb71]

its the obr just the top end kit ?

you can get the whole engine but what im talking is just the top end heres a link to all there top ends
http://www.oneillbrothers.com/rc-car/engine-parts/top-end.html

 

[smurfer69]

6311 - Full Mod G320RC Top End (Replacement for engine 6300)
$199.00
thats the 1 im thinking

 

[Z.hb71]

6311 - Full Mod G320RC Top End (Replacement for engine 6300)
$199.00
thats the 1 im thinking

that ones sick! 7.7hp supposedly.

 

[smurfer69]

yeah its on the 31.8 full mod g320
I think it was demoed on an RCsparks vid a while ago
maybe wrong ?

 

[Z.hb71]

yeah its on the 31.8 full mod g320
I think it was demoed on an RCsparks vid a while ago
maybe wrong ?

not sure, he also had the widow maker which magically dissapeared

 

[smurfer69]

I remember that, proberly a 1 off vid went wrong then deleted it

 

[Z.hb71]

I remember that, proberly a 1 off vid went wrong then deleted it

possibly,

 

[smurfer69]

well jb welded couple hours ago
just put exhaust back on,
fire it up tomorrow seen if holds,
and sounds ok, its a dominator
burbles like a drain anyway so might not make
any difference lol

 

[Z.hb71]

well jb welded couple hours ago
just put exhaust back on,
fire it up tomorrow seen if holds,
and sounds ok, its a dominator
burbles like a drain anyway so might not make
any difference lol

Yup, id header wrap it just to be extra strong.

 

[Z.hb71]

well jb welded couple hours ago
just put exhaust back on,
fire it up tomorrow seen if holds,
and sounds ok, its a dominator
burbles like a drain anyway so might not make
any difference lol

How did it go?

 

[smurfer69]

wish I could , but if I do I won't get screw, no way,
gotta hope for best, ive looked at spec for jb weld
and heat wise its fine

 

[smurfer69]

alright buddy didn't get round to it today,
another issue messing around with, gonna start sat morning ,
I will video it ,
ive looked at where I put jb weld I can hardly scratch it,
you can definitely tell the metal side of jd weld
amazing stuff