Gizmo1
Well-Known Member
Hi Guys,
i just finished these up as promised.
These are my IRP V2 Platform Tie Rods .
They will for sure fit the following models
XB,XT,XSC & XBE
Here is the item description:
Sold as a set of 2 , this will do one car
The center links are constructed of 6061 T6 Billet, they start out as 1/2" hex stock and then machined to round for a brilliant finish.
I leave a section as 1/2" hex, slightly off set of center, so you can hold the center link with a standred 1/2" open end wrench while tightening the jam nuts once your desired toe setting is set.
we then cut 2 small bands at one end to designate the outer ( goes towards the steering arm ).
the reason for this designation is the center links are tapped right hand and left threads.
the outer being right hand and inner being left hand
this allows super easy on car toe adjustment.
These particular units utilize New design rod ends that i had custom made for IRP.
i worked with the manufacturer over the last year or so to get these made up.
They are constructed of 4130 Chrome Moly Bodies, with Stainless Races , encapsulating the Hard Chrome Plated Balls... these bad boys are Butter Smooth and will take any abuse you can dish out !!
In the past the only option for the Chrome Moly ends were with Kevlar races, these are bullet proof as well but the downside has always been they were a little stiff due to the kevlar race, and they are VERY Expensive.
I have committed to a massive quantity of the new rod ends, damn near scarey, so the pricing was excellent, i can pass that savings on and the end user gets the benefit of the higher quality rod .
Each set of these new tie rods comes with
2x center links
2x RT Hand Threaded 4130 Chrome Moly , SS Raced , rod ends
2x LT Hand Threaded 4130 Chrome Moly , SS Raced , rod ends
2x right hand jam nuts
2x left hand jam nuts
4x high Mis alignment 6061 billet stand off spacers
1x Decal
1x written instruction sheet
These utilize the stock mounting bolts that come on your Redcat.
There is no loss of articulation , no binding, and these come with a Limited Lifetime Replacement Warranty.
Price is $ 75.00 Shipped USPS Priority Mail to the Lower 48
Please send me a PM throught the forum or email.
Pics:
Side Note
I am also working other projects for the Redcat Line
i will have a finished prototype of the rear camber links by the middle of next week, a quick fitment and test runs and they will be available soon !!
Thanks Guys and i look forward to working up more new products.
Buddy @ IRP
here is a vid of the V2's on a Baja.
the base installation is the same on a Redcat, with the excepetion of how the standoff spacers are mounted on the Redcat.
the written , included instructions explain how to mount the standoffs properly on the Redcat.
[ame]
[/ame]
i just finished these up as promised.
These are my IRP V2 Platform Tie Rods .
They will for sure fit the following models
XB,XT,XSC & XBE
Here is the item description:
Sold as a set of 2 , this will do one car
The center links are constructed of 6061 T6 Billet, they start out as 1/2" hex stock and then machined to round for a brilliant finish.
I leave a section as 1/2" hex, slightly off set of center, so you can hold the center link with a standred 1/2" open end wrench while tightening the jam nuts once your desired toe setting is set.
we then cut 2 small bands at one end to designate the outer ( goes towards the steering arm ).
the reason for this designation is the center links are tapped right hand and left threads.
the outer being right hand and inner being left hand
this allows super easy on car toe adjustment.
These particular units utilize New design rod ends that i had custom made for IRP.
i worked with the manufacturer over the last year or so to get these made up.
They are constructed of 4130 Chrome Moly Bodies, with Stainless Races , encapsulating the Hard Chrome Plated Balls... these bad boys are Butter Smooth and will take any abuse you can dish out !!
In the past the only option for the Chrome Moly ends were with Kevlar races, these are bullet proof as well but the downside has always been they were a little stiff due to the kevlar race, and they are VERY Expensive.
I have committed to a massive quantity of the new rod ends, damn near scarey, so the pricing was excellent, i can pass that savings on and the end user gets the benefit of the higher quality rod .
Each set of these new tie rods comes with
2x center links
2x RT Hand Threaded 4130 Chrome Moly , SS Raced , rod ends
2x LT Hand Threaded 4130 Chrome Moly , SS Raced , rod ends
2x right hand jam nuts
2x left hand jam nuts
4x high Mis alignment 6061 billet stand off spacers
1x Decal
1x written instruction sheet
These utilize the stock mounting bolts that come on your Redcat.
There is no loss of articulation , no binding, and these come with a Limited Lifetime Replacement Warranty.
Price is $ 75.00 Shipped USPS Priority Mail to the Lower 48
Please send me a PM throught the forum or email.
Pics:
Side Note
I am also working other projects for the Redcat Line
i will have a finished prototype of the rear camber links by the middle of next week, a quick fitment and test runs and they will be available soon !!
Thanks Guys and i look forward to working up more new products.
Buddy @ IRP
here is a vid of the V2's on a Baja.
the base installation is the same on a Redcat, with the excepetion of how the standoff spacers are mounted on the Redcat.
the written , included instructions explain how to mount the standoffs properly on the Redcat.
[ame]
Last edited by a moderator:
