New to site, getting my chimera soon!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
I

Innov8tiveTech

Junior Member
Messages
8
Reaction score
0
Hello my name is jordan I am new to the site. I am going to purchase a chimera on this Friday and wanted to know the "list" of the important things I need to do. I know I will need to put some tubing over my drive cups, possibly "vent" the fuel tank, and was told I should get the 7075rc diff housings. What else should be on my "must get" list?
 
Hello and welcome!

Go over the whole car and double check screws (tighten and loctite if needed)

Kill switch

Aluminum gear plate

Throttle and steering servo for peace of mind

Hpi air filter

7075rc diff housing like you mentioned

8K clutch spring

Diff cup sleeves

Wheel adapters if you want to run hpi wheels

Tuned pipe would be a great addition but not a necessity.

If this is your first 1/5th start reading and watching videos on break in and tuning.

I'm sure other will chime in with their inputs!

And remember to have fun. If something breaks know that it is as much fun wrenching, fixing as driving!
 
Last edited by a moderator:
What is the best throttle and steering servo for this system? I plan on getting lithium receiver pack as well what Is recommended? Also is the jet pro pipe loud, should I just consider a silencer as part of the cost?
 
Ohh by the way I've been in the hobby over 15 years strong and had a duratrax fire hammer, loved it, just wanted to get back into the big toys again ( I normally fly large scale helis). Thanks for all the help guys!
 
Innov8tiveTech said:
Also is the jet pro pipe loud, should I just consider a silencer as part of the cost?
Click to expand...
Yes its loud without the silencer but not as loud as a bartalone or victory pipe but much louder then stock.
 
I'm running a Hitec MG5645 for throttle and a 805MG for steering. They were leftover from an FG Marder Beetle that I had and I bought a Redcat roller from Ebay and put them in it. They work great!
 
Ok noted for servos. I've been in the hobby since 92' with my first nitro in 93' that being said, the first thing I purchased for it was the kill switch. Matter of fact I am not running it untill it has all of what I consider minimum upgrades. Last thing I want to do is pack up early because I was in a rush to run it.
 
Just finished venting the tank, added the kill switch, and fully cycled the receiver pack about 5 times. Also added and extension hose to the exhaust to clear the real tower/bulkhead cage 19mm and used ziptied

image.webp

image.webp

/monthly_2015_03/image.jpg.623bb2ba7272d2894c8830fb73d1e49f.jpg
 
Here is tank vent ( phone won't let me attach multiple pics)

image.webp

image.webp

/monthly_2015_03/image.jpg.08e2d20b1bdfaeec047f6e1912d74089.jpg
 
Found out I can fit the hpi axle boots on the chimera, going to put them all round.

image.webp

image.webp

/monthly_2015_03/image.jpg.c4e7146c365b5156695bc81da8f70273.jpg
 
So I can't seem to fit the 7075 rc rear shock tower for stock pipe, there is just no room to fit it I'm even without massive bending and cutting ( might as well just send it back and get the jet pro shock tower and wait to install untill I can afford to get the jet pro ) am I missing something, it's way to hard of an angle to install the pipe

image.webp

image.webp

/monthly_2015_03/image.jpg.f25f9d25ed4e8871e06b200d161b7593.jpg
 
Back
Top