Post Your Redcat Pictures Here!

[NitroBurn1]

Here is a picture of my MT5 next to my brothers Baja. Over the next few weeks I'm going to be adding an x-can and a race ported 29cc head kit. I did change the clutch spring to HPI's high response spring. It was bogging bad on take off without it. This truck definitely needs more power than a stock cy23. Also the front shock springs are a bit to short, you have to adjust the preload all the way down to take up all the slack. Even then at full droop there is a small gap. I plan to get the RAMTech 20%+ springs to fix this. Over all, this is the best RC I have ever bought.

 

[adr_ian]

Is that the stock ride height? or can you set it higher to get more ground clearance?

 

[Shiny]

Cool rides.

 

[adr_ian]

more pics!

 

[RAMTech-RC]

Here is a link to the Redcat Show Truck wth all the aluminum options added.

Redcat Rampage Copperhead

 

[Shiny]

Here is a link to the Redcat Show Truck wth all the aluminum options added.

Redcat Rampage Copperhead

Thank you for the link. Love it.
Not too crazy about the color thou.

 

[adr_ian]

nice...


how much lighter is that thing comparing to the original non-alu rampage mt5

 

[Shiny]

Probably allot of $$$$.
I am guising 1,500 + $ minimum.

 

[Large Scale Alloy]

Rob, when is that pipe going to become available through redcat?

 

[GH Racing]

nice looking cars

 

[RAMTech-RC]

Rob, when is that pipe going to become available through redcat?

I think in a few weeks.

 

[marderbeet]

how are these cars holding up?

 

[RAMTech-RC]

Like most new vehicles, there are some problems. But, it looks like we figured out most of them now, with either no cost mods, or low cost mods. The aluminum gear plate and FastEddy bearings solved the stripped gear problem.

 

[pipeous]

nice looking cars

Hey Martin, I see you have lots to say lol

I am grabbing one of these things. Should I bring it by the shop so you can make some goodies for them?

 

[pipeous]

http://s304.photobucket.com/albums/nn181/Pipeous/RC/Rampage_TT5/

there's mine. it's just new, but I got a deal on the buggy and got the stuff to make in an mt as well. going to try the redcat pipe out as well. so far I am liking it. break in tomorrow

 

[Chaos]

My RedCat...

Here is my bone stock Rampage...i love it











But bone stock is only so much fun....got me a new mill for it...

New motor is in and ready for...um parking lot circles and poser shots...lol/..gotta love the bling look..







more to come...i love this beast..4x4 rules.

 

[RAMTech-RC]

Make sure you get an aluminum gear mount. It solves alot of strength issues.

 

[Chaos]

Thank you for the adivce...will do

 

[pipeous]

I just got home from the offroad track. Last race was in September and the track is getting ripped up a bit for a new layout. It's an 8th scale track but a fast track and fun to play on. I used to take the Marder down there all winter... the puddles were massive and leaves everywhere. I dug channels in the dirt with a spike and a stick, used a small piece of 2x4 to push the puddles along ... we are having a big scale meet and greet there tomorrow, so I wanted to get the puddles draining... stupid me forgot the squeegee and my buggy shows it LOL. man that was fun. the drifts coming out of the corner onto the straight over a leaf section about 30 feet was fun. I am still taking it easy, half throttle or less to work the engine in but not many places you can go wide open anyway.... lost a dogbone pin today but Rob had one and I called him when I was coming home and stopped and grabbed one, plus some other stuff... anyway, enough babble, dirty buggy pics

 

[lancier]

Nigerian Brute Force MT5!!

Here are pics of my MT. This is the Africa Market version called the "Brute Force MT5" Comes with a factory installed 28cc CY engine. Hop ups so far are:
1. DarkSoul-RAMTech Extended Axle Kit
2. 6 Volt 5000mah Hump Battery Pack
3. Outerwears Shockwears Skull
4. Outerwears Pull Start Cover
5. Outerwears Pre-Filter
6. Futaba T3PM 2.5GHz FAAST Transmitter/Receiver.

Awaiting a Jetpro Side Pipe and Hitec Digital servos: HS5745/HS5645. Since ran 2 tanks thru the engine. The axle extenders gives the truck fantastic stability even on high speed turns.