Sold / Found Race ported 30.5

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Status
Not open for further replies.
46u

46u

Well-Known Member
Messages
1,263
Reaction score
8
Location
Macon, Georgia
If any one would like to check me out take a look at my eBay feedback user name vld35 or PM me and I will send you my phone number. If there is not any interest it will go on eBay.

I built this with all new parts and ran it for about a gallon if that. The only reason I took it out of my 5B because I was oval racing and it just had too much torque and was too easy to spin out on hard packed clay. It is a very toquey engine and runs very well.

It has a race ported top end from DDM see link below kit cost $90. The cylinder has been machined for the plus 2mm crank and not stacked gaskets. Machining the cylinder is the best way to go and in my opinion only way to go.
http://www.davesmotors.com/s.nl/c.885035/n.1/it.A/id.5892/.f
Team Fast Eddie bearings. Carburetor is a 668. I am not sure but I think I put a stuffed crank in it. When I took it out of my 5B took the top end off and inspected it all look very good. Sold as picture other then I will be taking the exhaust manifold off.

$125 plus shipping.

Fill free to ask questions and more pictures available on request. If you would like you can PM me and if you live in the US I will give you my phone number and we can talk about it. But please keep in mind I have limited minutes.
Thanks
Jeff
 

Attachments

  • DSCF7557.webp
    DSCF7557.webp
    26.3 KB · Views: 64
  • DSCF7558.webp
    DSCF7558.webp
    26.2 KB · Views: 58
Last edited:
Bottom dollar $125 including shipping to the lower 48 US states. If I do not have a takers by Saturday it goes on eBay.
Thanks
Jeff
 
Hey i'm interested in this motor but i have some questions due to the fact that i'm new to 1/5 scale vehicles.
1. Is this a bolt on to my king terminator 29.5 cc truck?
2. Will all my 29 cc parts fit this engine, pull start exhaust and so on?
3. What kind of power is this putting out?
 
ONEFASTTERMINATOR said:
Hey i'm interested in this motor but i have some questions due to the fact that i'm new to 1/5 scale vehicles.
1. Is this a bolt on to my king terminator 29.5 cc truck?
2. Will all my 29 cc parts fit this engine, pull start exhaust and so on?
3. What kind of power is this putting out?
Click to expand...

I am not real familiar with the King terminator but I am guessing it will. I know any parts from a CY or Zenoah will fit. This was built out of CY parts. As far as power it had too much for me when oval racing. Guessing, as it has never been on a dyno I would say around 4.5 HP but keep in mind what exhaust you run has a lot to do with the out put. If you would like I can PM you my phone number and you can call me.
 
46u said:
I am not real familiar with the King terminator but I am guessing it will. I know any parts from a CY or Zenoah will fit. This was built out of CY parts. As far as power it had too much for me when oval racing. Guessing, as it has never been on a dyno I would say around 4.5 HP but keep in mind what exhaust you run has a lot to do with the out put. If you would like I can PM you my phone number and you can call me.
Click to expand...

Shure man pm you'r number.
 
Hey man i called you but no one answered. I can offer you 100 shipped to Houston texas, let me know asap... Thank's
 
ONEFASTTERMINATOR said:
Hey man i called you but no one answered. I can offer you 100 shipped to Houston texas, let me know asap... Thank's
Click to expand...

Do not know what happen as it does not show a missed call. Did you get a recording? I have been away from Friday till today. I will pass on that price. The top end kit cost $90 alone. I have other offers standing but being I have been a way have not had time to talk to the others.
 
Status
Not open for further replies.
Back
Top