Rammer's RAMPAGE !!!!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
R

Rammer

Senior Member
Messages
98
Reaction score
0
After a LONG winter,I am almost done.Just need to hook up steering,and charge battery.Then I should be ready for some gas,and BREAK-IN... :D


Used alot of parts from RAMPAGEHOPUPS,he ships very fast,and is very


helpful.Don't buy your RAMPAGE parts from anybody else,you will just get ripped off. :eek:


Baja 5b parts fit very well used LOTS,.........SEE IF YOU CAN SPOT THEM !! :cool:
 
let me know how you go with the x-can and the long stingers


i had mine even supported at the end and they just f*#king come loose, i'm ditching it and getting a rdlogics pipe soon


Nice truck btw bro
 
speedbaboon said:
let me know how you go with the x-can and the long stingers
i had mine even supported at the end and they just f*#king come loose, i'm ditching it and getting a rdlogics pipe soon


Nice truck btw bro
Click to expand...
I used high temp epoxy,to glue it together.I wanted the exaust to fit under


the body.It will most likely fall off,and will have to think of something else.


It worth a try,I like how it looks with dual exaust.Might take the exaust to


the drillpress,and put in some self tapping screws,to hold it together ?


Let me know if you find a exaust,that fits under the body ? I would be very


intrested ......
 
Sprint 77 said:
Very clean work there Rammer , what kind of Red gears you got in that thing? Fill us in man we share our tips with you.
Click to expand...
Same Plastic gears as everyone.Just made black rubber gasket for the


gear cover.The red is high temp grease ,that has not spread around yet.


The intension was to cool , and grease gears,to last longer......
 
Sprint 77 said:
Very clean work there Rammer , what kind of Red gears you got in that thing? Fill us in man we share our tips with you.
Click to expand...
Here is a cool tip for you : Sprint


You know the silver tinfoil tape that is sold at hardware stores,to seal the


metal heating ductwork in your house ?


Cut thin strips ,slightly smaller than the bearing.Then tightly wrap the sticky


tinfoil tape around bearing.Will take up slack where the bearing won't fit right.


Bearing fits in the aluminum,and will be nice and snug,no slop....You might have to try a couple of times,you don't want to wrinkel the tape on the bearing,just take out the slack.If you cut the tape thin enough,you can't


even tell it was done , very cool , ha ha ha !!!!!!!


Your turn ?????
 
Excellent Rammer, that's what I'm talking about.....I have a ton of that stuff (foil tape) lying around and plenty of sloppy bearings too. I just never put them together. Thank you!
 
exactly correct. those long stingers create massive back pleasure and minimizes the power from your motor. i got rid of my 6” stingers and it made a huge difference. If you gradually increase the stinger diameter you can minimize the power loss. example go from the ½” to ¾” finishing around 1+ inches. Will help. I run a jetpro now and love it. Looks great but no good on the power loss
 
magnum57 said:
exactly correct. those long stingers create massive back pleasure and minimizes the power from your motor. i got rid of my 6” stingers and it made a huge difference. If you gradually increase the stinger diameter you can minimize the power loss. example go from the ½” to ¾” finishing around 1+ inches. Will help. I run a jetpro now and love it. Looks great but no good on the power loss
Click to expand...
Bought a new DDM DOMINATOR chrome pipe , should help with the POWER loss .... Still a little worried that it will melt ,my new PROLINE RAT body ???


I like the pipe ,but don't know how I am going to protect the body from the HOT pipe ??? Think a two or three layers of tinfoil tape will fix that???OR will I have to cut up the PROLINE RAT body ??? :eek:
 
Back
Top