Sold / Found HPI Baja #85474 - POWER CONTROL SLIPPER CLUTCH SET (57T)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Status
Not open for further replies.

vadn1

Well-Known Member
Messages
124
Location
Houston, Texas
Wanted

HPI Baja #85474 - POWER CONTROL SLIPPER CLUTCH SET (57T)

85474_85474_01p_800_600.jpg


Please message me or post here if you have one for sale.
 
Wanted

HPI Baja #85474 - POWER CONTROL SLIPPER CLUTCH SET (57T)

85474_85474_01p_800_600.jpg


Please message me or post here if you have one for sale.
I do have what your looking for. When I get home I'll take a pic. Like brand new. Buddy was going to build a track but never happen. Also never sold anything on line, just letgo and it was pickup only. I'll get back to you.
 
I’ve got a modded one so I can use what ever spur gear I want on it and enough spares to build another. I’d never sell that stuff. It’s also got a Ti layshaft as well.
You hear clacking when you land on throttle, I’m convinced it saves your transmission others say otherwise.

It is a bit more weight but with carbon pads and Ti layshaft it’s not much heavier than standard.

If you do enough searching you can buy the individual parts brand new. The standard one is poop IMO.

I’ve not changed my spur gear in 2 years. Got a standard Hostile on there, well with an enlarged hole to fit.
 
Last edited:
I do have what your looking for. When I get home I'll take a pic. Like brand new. Buddy was going to build a track but never happen. Also never sold anything on line, just letgo and it was pickup only. I'll get back to you.
 

Attachments

  • 16148201561166142233485663959390.jpg
    16148201561166142233485663959390.jpg
    131.3 KB · Views: 9
  • 16148201969086491017072291449075.jpg
    16148201969086491017072291449075.jpg
    117.7 KB · Views: 9
  • 16148202171618319700971178638187.jpg
    16148202171618319700971178638187.jpg
    99.7 KB · Views: 9
  • 16148202363135544980299988499151.jpg
    16148202363135544980299988499151.jpg
    72 KB · Views: 9
  • 16148202597865151586707059551344.jpg
    16148202597865151586707059551344.jpg
    133.9 KB · Views: 9
  • 16148202850286291565176955034773.jpg
    16148202850286291565176955034773.jpg
    133.4 KB · Views: 9
Show me but I don't run a slipper anymore. My mod was done with careful thinking and a case of beer.
Here you go mate, this is what I did. I had to go to my old university though and pull a few strings to use their lathe.

When you’re ready let me know your thoughts?
 
Last edited:
Here you go mate, this is what I did. I had to go to my old university though and pull a few strings to use their lathe.

When you’re ready let me know your thoughts?
Hey Milo Thanks for vid. I did my mod about 2013 and to tell you the truth I don't remember if it worked or not, but I think it did. In your video do see what changes are to be made to properly set up my spur but that could be for the other guy who buys it. Thanks.
 
Yes if you watch it carefully, when you sell it you can send the buyer my way on here and I’ll help them if they want to mod it or if you do.
 
Last edited:
he made me the top hat washer so i could do mine about 3 years....which i haven't done yet?
...well it was sumone off bfuk who made me it??
si (coalminer off bf-uk) made the top hat washers mike (y), at least he made mine for the slipper i have on my orange rail :)
 
Status
Not open for further replies.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock    No Thanks