Not Taylor rc🤔🤣

[RcJunkie13]

Is the guy that sold it messed up good and reputaple

 

[DougStar]

Yeah well poop happens the guy in question is not a builder the gap in the opposite pin clip was not 12 o'clock or 6 o'clock it was like off by a fair bit 10 o'clock so ill place money on the clip coming out

Is the guy that sold it messed up good and reputaple

 

[Z.hb71]

Yeah well poop happens the guy in question is not a builder the gap in the opposite pin clip was not 12 o'clock or 6 o'clock it was like off by a fair bit 10 o'clock so ill place money on the clip coming out

I bet that's what did it.

 

[RcJunkie13]

Yeah well poop happens

all jokes aside yeah that sucks, something that would only happen once , hopefully alx does something about it

 

[Milo]

Yup take for example when z was born, all jokes aside yeah that sucks, something that would only happen once , hopefully alx does something about it

I don’t think it was an ALX issue, it was a bad rebuild by someone else.

 

[Z.hb71]

I don’t think it was an ALX issue, it was a bad rebuild by someone else.

+1

 

[DougStar]

Just found out that akx said to the guy
"Need a special tool to remove the piston" im calling bs on that!. So alx sold him a complete crank with piston in place. So all he did was split the case install new crank/piston
New cylinder. So ......was alx that did the clip according to my mate

 

[Z.hb71]

Just found out that akx said to the guy
"Need a special tool to remove the piston" im calling bs on that!. So alx sold him a complete crank with piston in place. So all he did was split the case install new crank/piston
New cylinder. So ......was alx that did the clip according to my mate

That's a massive load of bullshit. No special tool , just a fekking screwdriver or needle nose pliers. And if he did the crank and piston assemble he needs to honor that poop.

 

[Relic-1]

Wow ! That's serious damage , looks like that mark isn't gunna come out , ( when somebody askdcwhst your R.C. costs in front of my wife ,, she still don't know what my ski boat cost , ten years ago , but maybe she's hidding her knowledge of these things, hmmmmm ,,,,,,

 

[DougStar]

Yeah ... so now it sounds like it will be sent back to alx for a rebuild this is good coz don't think I need to be jinxed with this motor
The first rebuild happened coz the motor dropped a small end and the rollers went through the ports and destroyed it thats when the new crank/piston assembly and cylinder was put in......
Sound like a bad voodoo spell to me

That's a massive load of bullshit. No special tool , just a fekking screwdriver or needle nose pliers. And if he did the crank and piston assemble he needs to honor that poop.

 

[RcJunkie13]

Z didn’t you bend a crank on ur 71 project, wasn’t that also alx?

 

[Z.hb71]

No, stripped the threaded crank stub. That was my fault because I was trying to drill start it by that little nut

 

[rcnut_14]

pfft, 4.8%? That's barely beer!

but seriously dude, that sucks. but hey, part of the hobby. sent back as in warranty? or are they making him pay for it

 

[DougStar]

Here is the piston and you can see how very little fuel its seen it was not a new motor but it just had a complete rebuild

Here is alx and his comment on the situation

 

[PortCityRC]

Wonder how long to rebuild? Being it took Haric months to get his new build

 

[szaki75]

was there a “c” or an e-type of clip used?

 

[DougStar]

Wrist pin came out so....the clip came out, not put in properly

and mentioned in my post above

was there a “c” or an e-type of clip used?

 

[szaki75]

it is maybe my bad English so i could not raise the question correctly.
which of these circlips the alx is using? (…that was probably not installed correctly)

 

[DougStar]

Ah right bottom left

 

[niz55]

That sucks man. I know exactly how it feels.