Search results

Thats a good point, i was thinking small order to start to test. Then again there is full force rc that seem to have good prices too, i always used boca bearings and know they are good.

Ydp, i see fullforcerc is another one

Great setup, im not going to get to crazy just using the clunk in the tank and the dubro for now, shouldnt let anything in with this setup....over 10 gallons of fuel and just replaced my whole gas tank as a whole for 16.00 cant beat it. Fresh filter and tank

Came across this bearing website thebigbearingstore.com online and they seem to have a vast selection on bearings, anyone ever order these and know if they are good quality? Prices seem to be good....

I have 2 of these killswitches i took 2 off the other one and set them both to 4v cutoff which it will never get that low anyway, either way i contacted the seller and he sent me a new set anyway as spares. Thanks

Would you habe a part number that will fit our fuel lines? Nevermind i see it but the cleaning process looks to be a hastle one they get clogged per other posts of people using them... i ran my truck yesterday haven't had a leak, maybe will consider in the future if i do get leaks

just incase anything does get by the clunk an added measure of not ruining or clogging my carb, i ran it yesterday and it seems to be ok , didnt notice any difference

I have redcat rampage vehicles and was told he inner diameter of the stock fuel lines is 1/8 so i bought dubro 340 filter but looking at the inner diameter of the filter it seems smaller han the fuel line, is his going to cause flow restriction?

Just noticed that the low voltage tabs probably shook loose from vibration and got lost. I was wondering why my car was turning off when I turn and it was because these tabs were missing so as soon as it goes under 6 volt it shuts the engine off and my voltage receiver pack is at 6.2 so figured...

No they are set properly, smooth throttle no sputtering

Amsoil dominator, sure keeps engines clean i know because i took apart a 30cc engine after 9 gallons of fuel thru it and it looked spotless

Anyone anyone else mixing 25 to 1 and find that their spark plugs are fouling up fast? After just a couple of runs when you look at the electrode it's black and the whole top of the plug. That's what is recommended in the manual but I was thinking about running maybe 28 or 30 to 1 are any of you...

Dynamite instructions are incorrect at least we are happy that he's running again. Instructions on the dynamite kill switch State polarity does not matter but apparently it does The polarity on the dynamite kill switch needs to be negative closest to the motor we had it reverse and it was...

I took out my vekta 5 to run today and during braking airen 2 tanks of fuel and it ran perfect. When I went to start it back up on the third tank of gas it will not start not even a pop when the choke is on. I changed the spark plug, I checked the ignition coil took the engine out inspected...

I may need to purchase a two-way Barb but I need to make sure what the inner diameter is I believe it is 1/8 of an inch if that's the case I can just get a Barb and connect two pieces together and extended about an inch and a half more that should be enough for it not to touch. Although the only...

Got my g320 installed but the fuel tank needed to be flipped for the dominator side pipe doesn't touch the gas cap, now i have he transfer port heat sink and the fuel lines are a tight fir to the carb. My question is how much heat can these fuel lines hold will they melt if they rub the heat sink...

https://www.ebay.com/itm/223020019205?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649 Removed from a new RTR

https://www.ebay.com/itm/223014922095?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649 New never used removed from a rampage MT

https://www.ebay.com/itm/223010397224?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649 Brand new

?....ok....thats what this hobby is about, i bet that will never happen again....cheers