FG MT Build...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Just make sure if you make one you do not depend on just the rear chassis to support the wheelie bar. It will bend it. Even with the one I have that bolts on the rear I make sure to use a piece of wire in the rear to allow it to be supported from the rear end as well as the back chassis.
 
Bigger the Better said:
Just make sure if you make one you do not depend on just the rear chassis to support the wheelie bar. It will bend it. Even with the one I have that bolts on the rear I make sure to use a piece of wire in the rear to allow it to be supported from the rear end as well as the back chassis.
Click to expand...

I know what you mean BTB and I thought about that too. I will be making it similar the way I made for my 5B:2guns:

So my design will be mounted on the chassis and somewhere on the shock tower or roll bar. It's hard to start on it until I get the pipe:no:
 
Received my KCR front bumper bar............I was sooooooo wrapped:2guns: but when I unwrapped it and installed it I'm not sure anymore. Something is wrong, it's out of square:no:

Are they all like this? Should email the shop I bought it from(UK)?

Let me know what you think...and any advice is welcome :helpsmilie:

IMG_0010.webp

IMG_0015.webp
 
Last edited:
wait till the first head on crash.

not good for the price. you need to buy two parts hey to moun that up, just bend it it your worried, but the time you send it back and get another one, if the shop dose that it will be ages.
 
I sent them an email yesterday and was told "if I'm not happy send it back and they will send it back to their supplier for replacement" which is fine by me. But like the above post it will take ages again for to received it:no:

I might ask a mate of mine see if he can fix it, he's a metal guru. If he can't then I'll send it back..............:sleep:
 
might be the best move time you send it from australia tom the uk, then they send itm to there supplier, then they send it back, then they send it to you could tke a while
 
benckie said:
might be the best move time you send it from australia tom the uk, then they send itm to there supplier, then they send it back, then they send it to you could tke a while
Click to expand...

I know mate. You looking at 4 weeks easy. Mind you I had to wait too coz it was out of stuck.

I might just to put up with it coz once I start bashing I probably will not notice it all..............coz I bash hard:2guns:....................:clown:
 
I tried but will place everything out of whack. I'm just gonna leave it as it is coz I'm sure one bad stack will be worst than what it is now:clown::clown::clown:
 
!!

Thanks man!

I have ride now a few rides with these car, its ride awsome.

For those, they will also get a XL botemplate (+6cm)!!!
Look about: http://alu-tec.de/assets/s2dmain.html?http://alu-tec.de/

marder535_579.webp

Alu-TEC Offroad Chassis mit 535 Radstand

CNC Gefertigt aus 5mm Alu

Das Chassis ist 60mm Länger als das Original
und Verbessert enorm das Fahrverhalten...

For a few euro's more they can color it!
magura.webp
 
what do you do about the side chassis plates not lining up to the pull start and the gear plate, ive notived yours don't line up in your pic,s would this cause more rear endf flex and gear msh problems ?
 
Last edited:
benckie said:
what do you do about the side chassis plates not lining up to the pull start and the gear plate, ive notived yours don't line up in your pic,s would this cause more rear endf flex and gear msh problems ?
Click to expand...

Were you referring to one of my pics? If so which one was it?
 
Back
Top