Just orderd 32 rovan 32 for dbxl

Thread starter #5

Andrew

Well-Known Member
Messages
75
Likes
47
Location
Australia.
I watched you videos today how much you spent on that beast and did you win that bash
 

evssv

Well-Known Member
Messages
1,592
Likes
987
Location
Bristol uk
thks..(y).ahh...not sure tbh but a rough guess its gota b around 1600-1800 quid so far...o_O..would b about 2300+ if all upgrades were bought new but I've had sum cracking deals :p....them vids r from bashfest so its jus blast round the oval untill it stops/wrecks/runs outa fuel...not really a race as such..more so see how long ur rig lasts....:cool:.....but i was flying if i do say so meself;)
 

Buzzsaw46

Well-Known Member
Messages
235
Likes
123
Location
S.E. MN
Good luck with the new mill. Hope it lasts longer the the 32cc Rovan engine I had. I didn't have very good luck with either of my Rovan engines.
 

JACKDADDY83

Well-Known Member
Messages
342
Likes
258
Location
Denver,Co
G'day crew just ordered the rovan 32 cc for dbxl . it comes on Wednesday yeh baby .hope it's ok just doing on a budget $ 211 au . any advice πŸ€”
There motors are pretty strong you probably want to order a walbro carb the clone carbs are not that great...congratulations πŸ‘ŒπŸ‘ŒπŸ‘Œ
 
Thread starter #11

Andrew

Well-Known Member
Messages
75
Likes
47
Location
Australia.
There motors are pretty strong you probably want to order a walbro carb the clone carbs are not that great...congratulations πŸ‘ŒπŸ‘ŒπŸ‘Œ
Morning mate thanks for letting me know I wasn't sure if I'd done the right thing. By going the cheaper way out hope it's ok Ps I worked out my wife after 25 years if you want something just buy some wine 🍷 and have a new motor when I sobered up πŸ€€πŸ‘.
nice (y) those motors seem like really nice budget motors (y)
Morning z.hb not the motor we were talking about mate (obr) but it will have to do only $211 au
Good luck with the new mill. Hope it lasts longer the the 32cc Rovan engine I had. I didn't have very good luck with either of my Rovan engines.
What happened to your motors ?
 
Last edited:

Z.hb71

Well-Known Member
Messages
1,380
Likes
698
Location
Manvel, Texas
Morning mate thanks for letting me know I wasn't sure if I'd done the right thing. By going the cheaper way out hope it's ok Ps I worked out my wife after 25 years if you want something just buy some wine 🍷 and have a new motor when I sobered up πŸ€€πŸ‘.

Morning z.hb not the motor we were talking about mate (obr) but it will have to do only $211 au

What happened to your motors ?
yeah i get you, enjoy it!!!
 

JACKDADDY83

Well-Known Member
Messages
342
Likes
258
Location
Denver,Co
I had my king motor 36cc for about 5 months never had a problem with it besides the carb kingmotor/rovan same company...carb depends on you Dave at DDM told me walbro 990 is the premier carb....opinions vary πŸ˜„πŸ˜„πŸ˜„
 

Buzzsaw46

Well-Known Member
Messages
235
Likes
123
Location
S.E. MN
My Rovan 30.5cc dropped a wrist pin washer after about 4-5 gallons, tore up the top end pretty good. The Rovan 32cc had some chunks of what appeared to be connecting rod casting flash go through it after only 1.5-2 gallons.

Never again will I buy a bargain mill, I built my last two engines from ESP kits. The stock ported 34cc just finished its second race season with close to 8 gallons of fuel through it and it still runs fantastic. The second is a race ported ESP 34cc but other issues kept that truck side lined for most of the season so it's only just broke in.

You will be very happy with the Zenoah, top shelf mills!
 
Top