- Thread starter
- #241
Thanks man not quite back yet. Still have another couple weeks into this house then I’ll get back to wrenching. Rc Motorsports did the paint job
Road to Glory. The journey for gold medals and sexy women
- Thread starter misterleon
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
MonsterAir
Lone Racer 🤠
If you need a hand lemme know
- Thread starter
- #243
Well I missed most of the fifth scale off road season but whatever life is long. Started working on a new Baja. This is a genuine hpi and was kept in great condition. Swapped out the hpi shocks for mcd rr5 shocks. The rears are basically a direct swap but the fronts are quite a bit shorter and require drilling into the actual arm. I’m worried about longevity for the fronts but I won’t know until the shake out runs. The old 34cc is coming out for a zenoah g260 with can muffler, obr bored 1242 and mod kill switch. Everything else will stay stock for now.
The rr5-e is back together and 100% charged up some batteries and gonna take it for a spin today if work isn’t too fiddlesticked up.
The rr5-e is back together and 100% charged up some batteries and gonna take it for a spin today if work isn’t too fiddlesticked up.
- Thread starter
- #244
Work was too fiddlesticked up. Will try again today
- Thread starter
- #245
Had an hour to spare today, ripped for like 5 minutes then handed the remote off to a guy I worked with. I told him to be careful. He said ok. Then he drove it straight into the fence.
He broke the front a arm. No problem though got home and fixed it up in about 5 minutes. This is my go to rig to just keep in the car for when I have free time.
Will try again tomorrow
- Thread starter
- #246
Made some progress on the Baja. Installed a new zenoah 26 with can muffler, obr bored 1242 carb, obr delrin velocity stack, tgn short stack and mod clutch. Mod killswitch is in, hitec 951 throttle servo, new outerwear’s. Waiting for the spektrum 9110 steering servo, rcmax clutch bell housing, bonehead engine braces.
MonsterAir
Lone Racer 🤠
What gearing and clutch spring setup did you go with?
- Thread starter
- #248
The mod clutch has 10k springs I think it’s 17/57 gears on it for now
- Thread starter
- #249
- Thread starter
- #250
- Thread starter
- #251
Put some time in on the fig’s suspension tonight. Laid down the rear shocks and adjusted the camber in the rear to -1 and front to -1. It came from the factory -1 in the rear and +2 in the front which is really strange
Also repaired the body from sundays bash. The front bumper was completely detached from the body. So a bunch of wood screws and job jobbed
Also repaired the body from sundays bash. The front bumper was completely detached from the body. So a bunch of wood screws and job jobbed
MonsterAir
Lone Racer 🤠
The bumper looks great it was mangled...
it was mangled...
- Thread starter
- #253
Yea cones and low bumpers don’t mix well
MonsterAir
Lone Racer 🤠
Yea cones and low bumpers don’t mix well
Well, I got more tires. If you can cut them down would cause less damage. Check out the video I put up in that 34cc thread, those are tires cut down to a couple inches.
- Thread starter
- #255
Where?
- Thread starter
- #256
MonsterAir
Lone Racer 🤠
Glad you didn't sell everything off wish I could come... We're counting on ya to put li on the map 
wish I could come... We're counting on ya to put li on the map
- Thread starter
- #258
Ready to go for tomorrow need to pick up a tent and I just realized I have absolutely no spares for the xr5 or fg. Hopefully if something breaks it’s a universal part
Nice why does the fg look longer or is that just that particular body
- Messages
- 13,208
- Reaction score
- 22,962
Better take a losi for back up when that junk breaks...