Finished TLR 5ive-B

[RC RT]

I was able to finish building my 5B and even gave a go at the paint.
View attachment 48621

Very nice

Looks like time to burn some fuel

been looking into doing custom body paint for my 5t 2.0, watching vid's,
but pricing slowing me down, have other upgrades higher on the list

 

[Squizzy Ralph]

Very nice

Looks like time to burn some fuel

been looking into doing custom body paint for my 5t 2.0, watching vid's,
but pricing slowing me down, have other upgrades higher on the list

Thanks. Working on break in now. I really like these servos and might upgrade my 2.0 also to them. Hitec D845WP

Awesome job! Which engine did you fit? And what kind of servos?

I used the zenoah g320 and use all three hitec d845wp.

Can see in this pic cutouts iv done
View attachment 48655
Got melt had to trim
View attachment 48656View attachment 48657

Your cuts look really clean. What did you use to cut the back by the starter. And what did you use for the rectangle shaped vents?
Also check out these schlock covers. I run them on my 5T and love them.

 

[RC RT]

 

[evssv]

I need me a bart...loads of servo horn clearance....
last pic...is the exhaust exit facing the chassis

 

[RC RT]

fegured out how to post

I need me a bart...loads of servo horn clearance....
last pic...is the exhaust exit facing the chassis

yes
thinking of putting a spacer under mout that should raise above and also change angle of exhaust pipe to add silicone tube
mount
need to proof read lol
That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it
If I have to will weld a tube to tube to get it out side
Just looked at DDM site the

Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845


NOW thru 6/19 $87.99
wifey NOT going to be happy

 

[crucialRC]

View attachment 48668

I don't think you will be able to use that pipe on a 5ive B. The way that pipe goes up, there will not be enough room under the body.

 

[Whoduh]

Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845

NOW thru 6/19 $87.99
wifey NOT going to be happy

don't forget to use coupon code LSF
Brings the price down a few more bucks.

 

[Squizzy Ralph]

I don't think you will be able to use that pipe on a 5ive B. The way that pipe goes up, there will not be enough room under the body.

+1

 

[evssv]

I don't think you will be able to use that pipe on a 5ive B. The way that pipe goes up, there will not be enough room under the body.

doug got one fitted on his ......

 

[crucialRC]

Here's my Victory pipe on my 5ive B and heat venting holes/mesh. Plenty of throttle/brake clearance.

 

[evssv]

fegured out how to post

yes
thinking of putting a spacer under mout that should raise above and also change angle of exhaust pipe to add silicone tube
mount
need to proof read lol
That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it
If I have to will weld a tube to tube to get it out side
Just looked at DDM site the

Hitec D-845WP 32-Bit, Multi Purpose, Waterproof, Steel Gear Servo w/Free DDM Alloy Horn DDM Deal of the Day for 1/5-6/19! Reg Price 104.99 - ht845


NOW thru 6/19 $87.99
wifey NOT going to be happy

that's not good imo....r barts this bad a fitting???my 5ive one fits sweet......whats this on btw??a 5 or 5b?

 

[crucialRC]

doug got one fitted on his ......

I didn't know that...guess it will work then.

 

[evssv]

I didn't know that...guess it will work then.

assuming this is a 5b bart....

 

[crucialRC]

assuming this is a 5b bart....

Pic looks like 5T

That pipe is for the 5t, didn't calm to be for 2.0 thought it would be ok, and I do plan on a 34 reed full mod later so going to keep it

Yeah, 5ive T.

 

[evssv]

ahh....mine hangs over side of chassis sweet....20181021_174933 by evssv, on Flickr
u have 2.0 don't u?is it a 2.0 bart or normal 5 bart one?

 

[Gamefan]

Your 5T looks sick!

 

[evssv]

thk u...

 

[DougStar]

that's not good imo....r barts this bad a fitting???my 5ive one fits sweet......whats this on btw??a 5 or 5b?

Yes i have a bart pipe on my 5b and it fits great
Had two issues the end was a bit short so i put radiator hose and clamp on the end. Getting the head pipe tight i had to mod an allenkey and cut the end off

 

[Tig]

Your 5ive B is sweet.
Cute pup to.

 

[Gaffle]

Yes i have a bart pipe on my 5b and it fits great
Had two issues the end was a bit short so i put radiator hose and clamp on the end. Getting the head pipe tight i had to mod an allenkey and cut the end off

What did you use to cut your allen key?