I think I need a new head for my Zenoah OBR Pro Stock

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
ChuenouXiao said:
Your thoughts on torque wrench?
Click to expand...
I use an old school beam style torque wrench. They're easy to maintain and can stand up to some abuse. You don't need an extremely expensive torque wrench for these engines. I believe I got mine for around $20 at Sears.
 
Deluge said:
I use an old school beam style torque wrench. They're easy to maintain and can stand up to some abuse. You don't need an extremely expensive torque wrench for these engines. I believe I got mine for around $20 at Sears.
Click to expand...
Is it necessary to have a torque wrench when rebuilding these engine? Or can it be done just as long as you tighten the screws good enough with loctite?
 
I also use a beam style torque wrench.Think I got mine at o`riely auto parts=$11.99. I think you torque them to 5ft lbs,I may stand to be corrected.
 
ChuenouXiao said:
Is it necessary to have a torque wrench when rebuilding these engine? Or can it be done just as long as you tighten the screws good enough with loctite?
Click to expand...
Some guys use them, some don't. I use one. The manufacturers don't provide torque specs just for the hell of it, they expect you to use them.
 
Deluge said:
He's using the Zenoah tool. I have that, but it's around $40. You can use two screws, but I'd get the HPI puller. This won't be the last time you'll need to take the flywheel off, so you may as well get the right tool.
Click to expand...
Why did he twist his tool so that the flywheel will pop? The tool you recommended here

http://www.davesmotors.com/s.nl/c.885035/n.1/it.A/id.4093/.f

Is it really going to do the job? It doesn't look like it has the feature to twist the flywheel like his Zenoah tool.... :(
 
No need to twist for removal. The key actually prevents it from spinning on the shaft. They just pop off like the clutch mount.
 
RCDAD said:
No need to twist for removal. The key actually prevents it from spinning on the shaft. They just pop off like the clutch mount.
Click to expand...
Thanks RCdad for your response, I appreciate it a lot :D .... sounds like it's not that hard to rebuild at all.... Just have to take my time that's all. It's actually fun too. I don't want the easy way out and simply buy a new engine. Just by rebuilding it... I will better understand my engine more. Besides.... this is a hobby.... if you pay someone to do it for you.... you're not getting the point of the hobby :D
 
I'm really thinking about using red loctite for the crank case bolt and flywheel.... what are your thoughts guys? Blue good or all red loctite? It is the engine and it will run hot....
 
Deluge said:
Negative. Red Loctite is overkill. A drop of blue will get the job done.
Click to expand...
But Deluge, my Jetpro's two bolt.... at first I use blue loctite and it didn't hold it. It vibrated and came loose. Now with the engine.... especially the crank case and the head bolts.... I would think red loctite would be ideal?
 
Did you let it sit overnight before you ran it? I've been using blue on all of the engine bolts without any issues. Red is overkill, especially with aluminum parts. Clean the threads, put a drop of blue on the bolts, torque them to spec and you're good to go. You have to give Loctite some time to cure, though. So, let it sit overnight before you attempt to run it.
 
Deluge said:
Did you let it sit overnight before you ran it? I've been using blue on all of the engine bolts without any issues. Red is overkill, especially with aluminum parts. Clean the threads, put a drop of blue on the bolts, torque them to spec and you're good to go. You have to give Loctite some time to cure, though. So, let it sit overnight before you attempt to run it.
Click to expand...
Should I use carb spray to clean the bolts with a metal brush?
 
Deluge said:
I use an old school beam style torque wrench. They're easy to maintain and can stand up to some abuse. You don't need an extremely expensive torque wrench for these engines. I believe I got mine for around $20 at Sears.
Click to expand...
For the torque wrench... how do you apply it to our L allen wrench? I guess what I'm asking is how do I use a torque wrench with our Allen Wrench?
 
Back
Top