- Thread starter
- #41
"not lookin for another wife as yet huh " Hmmmmmm....! Need to find one that will let me have more toys,I think I've worn this one out!
J.
J.
Let the build begin!!!
- Thread starter voo2doo
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
- Thread starter
- #42
charlieboy
Well-Known Member
very nice voo can't wait to see it finished 
- Thread starter
- #44
Here is the finished paint job.Its not de-masked yet nor has it had the protective film taken off so it looks a bit dull,but it will be off later on.Had a few bleeds though,nothing much but thats what you get for using old masking tape:2guns::2guns::2guns:
J.
J.
slawhammer
Well-Known Member
VooDoo..Lokks good my friend..Slaw
- Thread starter
- #46
More shots
Heres a few more shots of what it will/should look like.
J.
Heres a few more shots of what it will/should look like.J.
jackobyte
Well-Known Member
Looking good m8 lookin good.
charlieboy
Well-Known Member
looks like a propa bit of kit now mate, is it a shelf queen now or is it guna get used and abused?????????
- Thread starter
- #49
Abused!:2guns::2guns::2guns:
J.
J.
charlieboy
Well-Known Member
Trebor
Well-Known Member
how much for the wife
lookin good james
lookin good james
- Thread starter
- #52
Thats what it is being built for Charl.
Swap for your Leopard Keith
J.
Swap for your Leopard Keith
J.
mattc
Well-Known Member
Looking nice and shiney Voo. I bet you can't wait to give it a blast?
Matt.
Matt.
- Thread starter
- #54
And it will be BLASTED!!!! Matt.
J.
J.
- Thread starter
- #55
Hydro dilemma
Right people,i have just put all the elecs in and have come to a dead end.Where the hell do I mount the master cylinder for the hydro's??
:blink:
I was thinking on the lines of mounting it on the bulkhead brace? i don't want the push rod too long as I want all the 'umpf' possible. Can anyone suggest a mounting position to give the brake their full potential.
Cheers folks.
J.
Right people,i have just put all the elecs in and have come to a dead end.Where the hell do I mount the master cylinder for the hydro's??
:blink:I was thinking on the lines of mounting it on the bulkhead brace? i don't want the push rod too long as I want all the 'umpf' possible. Can anyone suggest a mounting position to give the brake their full potential.
Cheers folks.
J.
dwarfy
Well-Known Member
My mate has his mounted just to the back of the servo towards the battery. Seems to fit ok on his config which looks similar to yours although i think his servo is mounted further forwards giving it that extra space. Would it be feasible to mount it in front of the servo on a bracket fixed to radio plate & down to chassis then you got absolute minimum rod length?? Wouldnt need to be that big so wouldnt interfere with steering arms.
dwarfy
Well-Known Member
Are you limited by the length of your brake line?? If so looks like where you are showing is only option!
- Thread starter
- #58
Got loads of line mate,Zous sent me some(cheers Chris) Jackobyte has just left ,we had a tinker with the MT,jeeze there is a load to change when putting alloy on!Roll cage didnt fit,and had to mess around with the exhaust again to make it fit....knackered now! Comming on though.
J.
J.
dwarfy
Well-Known Member
Will be worth the effort when its all finished :cool2:
- Thread starter
- #60
Looks ok,just little fiddly bits ,nothing bad though.Just took some pics but the flash on the camera was rebounding off the truck so couldnt get any decent ones,i'll put some up tomorrow when,hopefully its finished........bling,bling!
J.
Oops!.....a coach has just pulled up......GULP!
J.
J.
Oops!.....a coach has just pulled up......GULP!
J.