What did the postman bring you today?

[DougStar]

Get outerwears and soak them in warm water and the print will come right off

 

[DougStar]

Warranty rally treads

An RMCK twin motor to work on

 

[DAVE1979SK]

he is finally home..

 

[DougStar]

he is finally home..View attachment 76796

Congratulations

 

[DAVE1979SK]

Congratulations

Thank you bro..
More photos..

 

[DougStar]

Massive shout out to Michael Lucre @Team Ninja Pro for making and shipping out this fantastic switch to meyour a good egg

 

[RcJunkie13]

Massive shout out to Michael Lucre @Team Ninja Pro for making and shipping out this fantastic switch to meyour a good eggView attachment 76945

I’m disappointed that you couldn’t make that

 

[DougStar]

Didn't ask for it Mike just made it for me

 

[Seandonato73]

I’m disappointed that you couldn’t make that

And this is why no one helps you out, smart arse.

 

[spents]

today the postie fetched me a surprise package ,
from bonehead dean, he had some pins made up and sourced some steel rings to replace the rubber o ring pin retainers,
i asked him where he got the steel rings, he sent me a set ,
dean has a kv5tt ( mgm e word converted) and he's been losing front drive pins left right and centre so he wanted to find an alternative to the rubber o rings,

 

[PortCityRC]

Thanks again to Jon Hall from Joker Designs for the new revised wrap

 

[blackrain]

Thanks again to Jon Hall from Joker Designs for the new revised wrap

Nice you had them change the name

 

[PortCityRC]

Nice you had them change the name

Yes sir!!!

 

[DougStar]

Brp 190 and splurge red thangs lipo and outerwears, filter oil , new linkage

 

[spents]

today the postie fetched me,
bear with me on this cos theres a story here ,
so a while ago miles @Milo asked me if i'd make him an exhaust bracket for his lightweight build and for the bzm pipe,
i said course i will, miles said how much, i said don't be daft were friends,
anyways, miles decided he was sending me a futaba 4pls as payment, he didnt need to but i aint gonna turn it down ,
so thank you very very much miles, spot on ,
story not finished yet but will continue between the pics ,

so, 4pls with two rx's ,



so miles and me had a bit of back and forth on the phone etc,
we came to the conclusion that his mecatech master cylinder would need relocating inboard a tad as well so he could use the bzm pipe,
so thats the deal, i make miles a couple of nice brackets, a relocation one for the master and an exhaust bracket which is gonna have to be some sort of swan neck bracket i think,
so also in the box is miles spare mecatech master cylinder, the original bracket for the master, and the original bzm pipe bracket so that i have sommat to work from,
miles is also gonna email me a few measurements and dimensions as well, then i can build the brackets off my own baja chassis,
either miles or me will update his build thread as brackets take shappe etc,
thanks again miles ,

pic of miles master and original brackets below ,

 

[Milo]

Top man Paul. Thank you so much.

 

[spents]

Top man Paul. Thank you so much.

yer welcome miles , or ya will be when i get the brackets made

 

[spents]

today the posties fetched me a set of BuRP's and adapters for the vekta from taylor rc ,
these will be stored for a little while untill i get a few more parts and get the vekta big bore ready ,
or they may get used ,



just slid a pair over the stock hexes to see what they looked like ,



tbh there aint a great deal of difference height wise between the stock tires and the brp's ,
depends where ya measure em really, they just look strange at first cos there deep dish and make the vekta much wider than stock ,

 

[Milo]

Boom.

 

[DougStar]

Yeah the offset is quite big on the brp's just don't get them wet but I know you got that covered coz you don't bash when its soggy out looks great