- Messages
- 1,296
- Location
- Spoklahoma Washington
Well that just makes my day , that fixes everything for me !!
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I run the winged clunk in all my rc, and about half my saws. I believe it was originally for flight, but it's great at keeping fuel flowing. Which was an issue in my old dbxl. Get down. To about 1/4 tank amd I would have intermittent fuel issues. Winged clunk solved that.Installed the upgraded fuel system.
Gave it more thought, and while I was initially convinced about my inline filter removal ... I've been flying large scale RC airplanes (kit builder) with radials and multi-cylinder engines up to 250CC and I've always been very careful with fuel delivery in the planes. Obviously extremely important to keep fuel flowing in all orientations, and to eliminate bubbles from entering into the fuel lines and causing issues.
I figured this would be equally important with a big truck like this, landing and jumping around, sloshing fuel in the tank.
So I installed along with the high-flow fuel kit, and 1 way vent setup ... my usual. Combination fuel filter, and small reservoir setup that holds around 2oz of fuel closer to the carb. Having a fuel reservoir means that if the clunk introduces bubbles (this can happen more frequently when the fuel level decreases in the tank) or lifts outside of the fuel temporarily, there's more than enough reserve fuel closer to the tank that the fuel flow should remain steady without bubbles or leaning of the mixture. Theoretically, if you're able to balance the truck up on its nose, you can run without issue. Much more like a real monster truck ... the next level upgrade to that, is a winged felt clunk that soaks up every last drop of fuel inside the tank.
The tanks in RC airplanes are typically designed so the clunk and line connecting the clunk, is centered in the middle of the tank. That way if the orientation of the plane changes, the clunk can reach all corners of the tank. The way the tank is designed on this truck, the clunk is effectively stuck in one corner of the tank. So if your truck is getting low on fuel, and is leaning over on the right two wheels (banked turn, side of a ramp etc. etc.) the clunk will for sure be outside of the fuel mixture ... in comes the reservoir.
So, long story short ... that was also the idea of the smaller filter as well, that it would add a tiny bit of extra fuel to the lines while filtering any fibers out introduced by a felt clunk without it reaching the carb.
Sorry ... but honestly, if you seal and secure the filter properly. I've never had a single flame out with airplanes or otherwise, so I humbly disagree there but it did prompt me to do a better job overall than what I initially setup. So thank you there!
There's an added benefit with my setup as well since I have a T at the entry point of the filter. I have an easy way of removing all of the fuel from the tank as I've extended a drain line with a plug out the side of the chassis that is hidden by the body of the truck. I have a small adaptor that allows me to quick connect my fuel can to that line, and pump out all the fuel from the tank. Again ... from the RC airplane side of things.
I just let mine sit wherever I have space for them. Never had tires deform on a 1/5 scale.Nice, the winged clunk is definitely the way to go I think.
All finished up, just waiting to run. Debating buying a set of 4 of the purple anodized beadlocks and a couple of the wooden stands Primal offers.
How are you guys storing your trucks? Just leaving these beasts on the wheels or is there something that holds the truck up and gives the suspension and tires a bit of a break. Seems these tires are pretty tough though and don't really deform much.
Nice, the winged clunk is definitely the way to go I think.
All finished up, just waiting to run. Debating buying a set of 4 of the purple anodized beadlocks and a couple of the wooden stands Primal offers.
How are you guys storing your trucks? Just leaving these beasts on the wheels or is there something that holds the truck up and gives the suspension and tires a bit of a break. Seems these tires are pretty tough though and don't really deform much.
Mine stays on a folding step stool. Keeps the tires off the ground and allows the suspension to not sit under full load. Have done this for years and never had an issue.Nice, the winged clunk is definitely the way to go I think.
All finished up, just waiting to run. Debating buying a set of 4 of the purple anodized beadlocks and a couple of the wooden stands Primal offers.
How are you guys storing your trucks? Just leaving these beasts on the wheels or is there something that holds the truck up and gives the suspension and tires a bit of a break. Seems these tires are pretty tough though and don't really deform much.
I got my folding one from Amazon. Its 9" tall I believe. Was right around 11 bucks.That’s a good solution Rick. Maybe I’ll try to find a small stool like that. I’d prefer not to sit it long term on the springs.
May I add sir...you were one of us..but bailed on your Raminator..sold it off like a second hand misfit toy lol.Ya ya ya ,,,, you luck raminator owners , everybody wishes they had your problems
That thing is beautiful! I wish I would have waited and got this..but had no idea it was coming out when I purchased my V2. I have done so much to my V2 I cant justify grabbing a digger.Nice
Still have yet to run mine, but upgraded the outside beadlock rims and the hubcaps. The purple anodized beadlocks are awesome looking. Left the stock green on the inside, and purple on the outside. Between the new hubcaps and the beadlocks, this thing looks amazing.
Set the spring pre-load up to have a bit more; sits much nicer now and has more usable shock travel than how the shocks came set with preload; no idea how it handles yet but I'm now 100% out of upgrade components short of pulling the diffs apart which I probably should've. That's the only thing I didn't mess with.
Have a new Futaba 10PX radio coming so I can use an additional channel as a light switch. Right now I have everything running on a 4 channel receiver (no need for a 5th or 6th channel just to hook up the voltage display; just need another Y cable) but I like being able to control the headlights from the remote, and will probably upgrade to rear-steer as another project a bit later on.
Register and gain access to Discussions, Reviews, Tech Tips, How to Articles, and much more - on the largest Large Scale RC community for RC enthusiasts that covers all aspects of the Large Scale RC!
Register Today It's free! This box will disappear once registered!
We get it, advertisements are annoying!
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.