- Messages
- 13,105
No new job started. 6 to 2:30. I've been patient and not tried to be too hard hard on Zed, but for crying out loud, it's time to get some poop figured out.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I am what I eat ??
Go to harbor freight and buy a fiddlesticking caliper you cheap ass. Good god, you cant check poop if you cant measure poop. And btw were in America we measure in inches and thousandths. Now take your pinion gear off and start measuring to see if the gear is out of round or not. Christ set this pinion against the stock one to check. And see if any teeth stick out farther. Did you put the clutch bell on a straight edge? Use your garbage old calipers for that, or a ruler. Start speaking stuff out or throw it in the trash and get a new set up. don't ask for help then say I cant because my other poop is broken when you just went through 5 spur gears, 2 of which would have covered the cost of a cheap dial caliper. And don't throw a little female dog fit that I scolded you. I'm sick to death of hearing the same regurgitated my poop is broke and I don't know why. Time to find out or stock up on spur gears.
My money is on the spur gear carrier being slightly off. Z ,I could send you my Hostile spur gear and carrier and and the pinion and see if it's any better.Take a look . Here's the spur and pinion back in,
Here's in one position, and when I roll it over to a different spot look how tight it gets. I'm thinking about doing what Mr.C said, go with a stock clutch bell and pinion and see how the mesh it.
View attachment 63873
View attachment 63874
Btw layshaft ain't bent. Check it, and spur gear runs true.
There we go??
If it was the Gear carrier the gear mesh would always be tight or loose . Its not. It goes from tight in one spot , to loose on the other side. Like a bent layshaft or a bent clutch bell. I have put a straight edge on the cb, and it is indeed bent . I am going to buy new calipers soon.My money is on the spur gear carrier being slightly off. Z ,I could send you my Hostile spur gear and carrier and and the pinion and see if it's any better.
If it was the Gear carrier the gear mesh would always be tight or loose . Its not. It goes from tight in one spot , to loose on the other side. Like a bent layshaft or a bent clutch bell. I have put a straight edge on the cb, and it is indeed bent . I am going to buy new calipers soon.
A ps for everyone else, ????
Yeah they are cheap, $15 here ?. I'm going to hold off buying one for now, As I'm waiting for a response from vertigo, to see if maybe they will warranty it , doubt it but I thought it's worth a go considering it has less that 4 gallons on it.Well Z hopefully you've finally found your issue, a tight mesh would cause heat then loose mesh would try ripping the teeth off the now hot spur.
Can get a stock clutch bell for about £10 here so pocket money for you.
Keep us updated with how you get on.
Oh I'm sorry I forgot you know it all . Sorry I tried to help. I'll make sure not to make that mistake again.If it was the Gear carrier the gear mesh would always be tight or loose . Its not. It goes from tight in one spot , to loose on the other side. Like a bent layshaft or a bent clutch bell. I have put a straight edge on the cb, and it is indeed bent . I am going to buy new calipers soon.
A ps for everyone else, ????
Why are you so defensive??? I didn't say anything like that nor was I implying that ???Oh I'm sorry I forgot you know it all . Sorry I tried to help. I'll make sure not to make that mistake again.
Just say your sorryWhy are you so defensive??? I didn't say anything like that nor was I implying that ???
Don't apologise for others confusion.Just say your sorry
Zeldas on a roll here lately, hence why I chewed him out earlier.Oh I'm sorry I forgot you know it all . Sorry I tried to help. I'll make sure not to make that mistake again.
Zenna worrier prince ? ???? more fitting don't you think???Zeldas on a roll here lately, hence why I chewed him out earlier.
Guess i might as well repost this here where it belongs....
View attachment 63896
Both y suck on this ?????????????Zeldas on a roll here lately, hence why I chewed him out earlier.
Register and gain access to Discussions, Reviews, Tech Tips, How to Articles, and much more - on the largest Large Scale RC community for RC enthusiasts that covers all aspects of the Large Scale RC!
Register Today It's free! This box will disappear once registered!
We get it, advertisements are annoying!
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.