- Messages
- 5,828
- Location
- Maryland, USA ??
- Thread starter
- #581
Mine was used with engine, pipe, servos and radio.
Crucial Kraken Vekta.5
- Thread starter crucialRC
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
- Messages
- 1,065
- Location
- Southern California
Good price. You didn’t have to assemble it and it came with zenoahg320 engine and servos??
if you guys are looking to buy a vekta, search the vekta Facebook group, I see quite a few for sale on there.
- Messages
- 5,828
- Location
- Maryland, USA ??
- Thread starter
- #583
I thought it was a 32 zen but turned out to be a 29 zen but I think it had work done to it.
- Messages
- 5,828
- Location
- Maryland, USA ??
- Messages
- 19,475
Looks nice ??
- Messages
- 1,065
- Location
- Southern California
Lol now go see if it fits??
any feedbacks, suggestions, complaints etc will be greatly appreciated??
- Messages
- 5,828
- Location
- Maryland, USA ??
- Thread starter
- #587
Got it in. I couldnt wait??
? First off it looks killer. If using the Axis stand mount, it will not grip around the front of the box. I will see if i can give you some measurements to possibly overcome this obstacle. Whoever installs it will need 2 grommets. Luckily I already had a couple on hand from another project. Got em from Home Depot so no biggie there. The Hilantronic throttle servo must be like 1-2mm wider than the servo you used cause it pushed the box just enough so the screws wouldn't go straight in. No biggie there either. All I had to do was loosen the servo top mounting screws a few turns then install the box mounting screws then tighten the servo screws back down. I added some foam to the bottom of the tray to protect the battery. After putting the lid on it, with the 7200mah battery I would've loved just a little bit more real-estate on top to bundle the wires and put the killer bee circuit board in it. I think a slight mod to the lid would correct this. All in all I think this thing is sick tho??and I'm geeked that I'm the 2nd person with one. Thanks Haric??
? First off it looks killer. If using the Axis stand mount, it will not grip around the front of the box. I will see if i can give you some measurements to possibly overcome this obstacle. Whoever installs it will need 2 grommets. Luckily I already had a couple on hand from another project. Got em from Home Depot so no biggie there. The Hilantronic throttle servo must be like 1-2mm wider than the servo you used cause it pushed the box just enough so the screws wouldn't go straight in. No biggie there either. All I had to do was loosen the servo top mounting screws a few turns then install the box mounting screws then tighten the servo screws back down. I added some foam to the bottom of the tray to protect the battery. After putting the lid on it, with the 7200mah battery I would've loved just a little bit more real-estate on top to bundle the wires and put the killer bee circuit board in it. I think a slight mod to the lid would correct this. All in all I think this thing is sick tho??and I'm geeked that I'm the 2nd person with one. Thanks Haric??
- Messages
- 17,175
- Location
- Crafers South Australia
Now it's a proper bling wagon ???
- Messages
- 5,828
- Location
- Maryland, USA ??
- Thread starter
- #589
Ready for a shelf?
- Messages
- 17,175
- Location
- Crafers South Australia
- Messages
- 5,828
- Location
- Maryland, USA ??
- Messages
- 13,102
- Messages
- 19,475
That box looks feking sweet in there ???
- Messages
- 1,065
- Location
- Southern California
Noted! Grommets are in order and they will be included. The top cover is 1/2 inch tall. I will see if i can go 3/4 tall without hitting the steering bellcrank.
- Messages
- 5,828
- Location
- Maryland, USA ??
- Thread starter
- #595
Nah talking about sloping up another 3/4" after the switch. It would clear the steering arm??
- Messages
- 19,475
- Messages
- 1,055
- Location
- Florida
Damn that looks fuego ?????????
- Messages
- 1,065
- Location
- Southern California
Not right now, maybe later on I’ll throw a few on egay or offerup. It’s only exclusive for LSF members, and a few of my friends has them.??
- Messages
- 19,475
Ah ok ?
- Messages
- 444
- Location
- Florida
The difference is... you don't have a Vektaman I just want a Vekta so bad. I can afford it its just damn it still is just expensive. Whats the difference between the LSE and regular Vekta 5?
Afaik the only difference is that one is a kit with no electronics and one is an assembled roller. I've been known to be wrong though.
Last edited: