- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #981
Yop sure is ?? made some beautiful 11 on the feild??
Doug's hpi 5B SS
- Thread starter DougStar
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
- Messages
- 1,811
Very nice! Much better run this time! Atleast someones getting in on some good rc action?
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #983
Yes it all went a bit smoother this time?? did lose some hardware ? but its an easy fix + shocks held up??
John Parks
Print my own
- Messages
- 4,021
Very nice doug, shes flies. Seems like you could go up a tooth size though (or more) she runs out of gear fast.
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #985
Its running 25/49 at the mo?? I do have 26/48 on hand?? and bet I could lean it out a touch more?
British Menace
Well-Known Member
- Messages
- 77
- Location
- Quad Cities, Iowa
The Baja 5T wheel axles. Are they M6 thread?
Regards
Regards
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #987
Not sure what you asking ?
front / rear?
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #989
- Messages
- 13,120
?????????dear doug,
have ya had another run yet ?
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #991
????
- Messages
- 1,811
Nice ? Doug ???!
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #993
So on my outing I lost the hardwear between the front and rear chassis ? all 4???? so as usual I go out with bits and bobs for running repairs ??. I had the correct screws to repair/replace them but........ lost a fixed modified chassis nut? iv had to strip her down a bit to get it sorted ?
?? so as usual I go out with bits and bobs for running repairs ??. I had the correct screws to repair/replace them but........ lost a fixed modified chassis nut? iv had to strip her down a bit to get it sorted ?
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #995
Yes easy fix ?? thank fek? had my 34 reed in here for 2 years no issues ??
......still like to dig up the twat that designed the baja and shoot him in the foot ? pluck his budgie and send his horse to the glue factory ? ?? what a ball ache ??
?......still like to dig up the twat that designed the baja and shoot him in the foot ? pluck his budgie and send his horse to the glue factory ? ?? what a ball ache ??
KevTrem
Well-Known Member
- Messages
- 897
- Location
- Newcastle, UK
I'd be doubling up on the nuts where possible (check nuts) or buying some heavy duty lock nuts, similar to Nyloc but with metal instead of nylon.
BTW its ripping Doug, watched your video from the other day, you did well with that summersault cartwheel, 8/10 for that.
BTW its ripping Doug, watched your video from the other day, you did well with that summersault cartwheel, 8/10 for that.
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #997
? ? lol yip it was quite a lawn dart?
The s spikes hook up real easy ? ill have to watch that ??
KevTrem
Well-Known Member
- Messages
- 897
- Location
- Newcastle, UK
? ? lol yip it was quite a lawn dart?
The s spikes hook up real easy ? ill have to watch that ??
Yeah looked like you had a couple of traction rolls. Mind your wheels held up well even after those tumbles, hopefully they last.
- Messages
- 17,175
- Location
- Crafers South Australia
- Thread starter
- #999
They are hard ...as in no give so big shock impacts is where you'll see damage ?
KevTrem
Well-Known Member
- Messages
- 897
- Location
- Newcastle, UK
you loaded them up well with your tumbles, but hopefully any breakages will be in the cheaper rim rather than the centre, easy to carry spares too.